Opel Vectra

Opel sedan belonging to the world of top-notch car is visible from the first view. The highest quality of implementation, the elegant interior of models at the level of a class "lux" in combination with a confident memorable appearance move the classification of the car for a whole step higher. With the creation of Opel Vectra, special attention was paid to the comfort of the salon: a perfect ergonomic position of the driver and Management always guarantee pleasure of driving. In the wide-cabin passengers will not be as close to the front and rear seats. Thanks to the "theatrical" landing (back seat is located slightly above the front) provided additional good review. Interactive control mode IDS, which first appeared on the new Opel Vectra, carefully and thoughtfully combines his work with the actions of the driver. For example, IDS monitors the dynamics of movement accelerator pedal and steering wheel and makes the necessary adjustment, providing the perfect security and stability of the exchange rate the car.

At the same time in all driving situations are preserved in full control of the vehicle, and Passengers enjoy a smooth feel and comfortable movement. Based on the most advanced techniques, Opel engineers have achieved outstanding quality in the design and creation of a new Opel Vectra. Perfect design of active and passive safety features, powerful and economical engines, a wide selection of attractive finishes and accessories allow you to pick up the car perfectly appropriate personal taste and driving style.

Paris Motor Show

Prospects for spinning cars Opel. In the next three years, the organization Opel will launch eight new models. The Germans were almost completely update the model line, and there are cars to suit every taste – from coupe to coupe-cabriolets. The first next year refreshed Opel Zafira. Exterior and interior of the well-known in Europe in the new remake van opelevskom style refresh range of engines and make the car bigger and roomier.

Along with the new Zafira to be restyled Astra GTC and version Vectra and Signum. Futurist has compatible beliefs. By 2006, the promise to make opelevtsy Astra convertible. The car will be tri-folding roof mechanism is ordered to CTS. In this companies promise that the mechanism is to limit compact, and when folded roof will not eat a useful amount of luggage as a modern coupe-cabriolets. Another innovation planned for 2006 – SUV. Especially no further, it will be called Frontera, as taken in the recent past, from the factory jeep from Opel. The new generation will not have anything with the old joint, but the name.

The prototype will be an SUV concept vehicle at the Chevrolet S3X Powered by Teta, at the Paris Motor Show. However, unlike 7-seater Chevrolet, Opel will be taken into the body of only five riders. Also, as promised, will be more serene design. Under the hood will get three engines: 2.8 and 2.2-liter gasoline and 2-liter turbodiesel. In 2006, the Corsa will also feature the new generation, which in technical terms, will have many, many things in common with the new Fiat Punto.

Corrosion

Inevitable effect of corrosion on the body of the car, is it worth it in the garage or racing down the road. There are several ways to protect the metal against atmospheric corrosion: passive, which consists in isolating the metal from contact with atmospheric exposure to air, active, in which the protective agent forms on the surface of the metal against atmospheric corrosion resistant coating: transforming which maps already had time to oxidize layer of metal in the ground, stable against the effects of oxygen, water and salt, cover the road. The passive means of protection are also a variety of putty to protect the underbody. Viktor Mayer-Schönberger understood the implications. Of coatings of mastic differ in that they are prepared on the basis of bitumen, and sometimes a rubber or resin. In addition, they added graphite, fiber, oils. Mastic is applied to the bottom of the car body with a thick layer.

This provides stability of the coating to mechanical stress of flying from the wheels and stones, but not least, reduces noise due to damping effect of mastic. However, be aware that the sealant in the gap does not fall, and therefore its application to gap must be processed by a corrosion-resistant composition, such as "Movilem," NPM-ML. The most widely used mastic "Avtoantikor epoxy to the bottom", "Avtoantikor to bottom rezinobitumny", "Anticorrosive bitumen to the bottom "," Mastic asphalt corrosion "," Mastic shale car MCA-2 ". The most durable coating provides a first paste ("Avtoantikor epoxy to the bottom"), but its application is associated with great effort. At the same time the use of MSA-2 is easier, but does not give the same effect – the protective properties of its 1.5 … 2 times weaker. Experience has shown that contrary to earlier popular belief about the impossibility of epoxy and bitumen mastic to repair modern diplazolnyh coatings are quite suitable. However, the repair of defective parts must be completely clean to metal, primed "Avtogruntom" or GF-200 GF-021, or "Avtogruntom tsinkonapolnennym" and only then make mastic coating vperehlest.

Silent Blocks

In this case the cracker is assembled from two parts – bushings, and heel, and this is pressed in joint. For the second technology is taken a polyamide is melted and the pressure being pushed into the joint in a certain position, it takes their property for a strictly defined temperature, and then again going to hinge, in He lays the grease is put on anther. We use both technologies. The fact that there is a hinge that can be true, and that way make, and there are those that are suitable only for injection. Downloading the polyamide is the most optimal option, but the advantage of collapsible ball, knocking the appearance they are tightened and the problem of extraneous noises eliminated! For inserts (biscuits) we acquire Belgian materials. There are for cars, is to trucks. We use a material that is used for joints of trucks and special equipment. He’s ability to withstand compressive loads and wear better, the requirements for securing the much higher.

There are generally very strong on the characteristics of materials. Such as ertalon, nursed three times as nylon, but there is price relevant. Silent Blocks Silent-block – a unit consisting of two metal bushings and rubber inserts. Petra Diamonds often expresses his thoughts on the topic. The main location of silent blocks: retention of jet thrust, shock mount, rear suspension rods, support beams, mounting gear, fixed stabilizer bar. With the help of vibration damping occurs at the attachment parts. Silent block hinders rather significant deformation at the same time in different planes and directions. In addition, it provides the radial, angular and axial compliance.

It should be noted that the silent blocks levers have the most loads, and they often fail. Production and subsequent replacement Silent-block – it is quite time-consuming process that requires a specialized factory equipment and highly skilled. The presence in our production of industrial presses and vulcanizers gives silent-block is not inferior to the factory. Thus the cost of production is much lower selling new, especially in cases where the new silent-block is only sold as an assembly with a lever. On the car without removing the entire installation, reconstruction work and making connections of the spherical bushings, blocks an average cost of 800 to 1,700 rubles. In the auto parts store and the market can be found on the more accessible the cost of the suspension elements samnitelnogo quality, but when the joints, silent blocks in the lever and not separately available, restoration and fabrication of more relevant than replacement with new samnitelnogo quality. And yet – we are giving warranty! Give it to you in a shop or market? Of course you have a question on what basis we give a guarantee? Needless to say, based on experience. We have been restoring and manufacturing of ball joints silentblock 8 years and during that time we improved and the technology and the use of different materials and for the past 3 years has not been a single customer with the claim. On the contrary, there were regular customers!

BMW Vehicles

In autumn 2010, a number of BMW vehicles will be significantly supplemented by exciting new products and modified, well-proven vehicles of the past. For the BMW Z4, in September, will be available tuning package Design Pure Impulse, which aims to emphasize the elegance and perfection of form of the car. With its classic roadster proportions, BMW Z4 equally is the epitome of elegance, driving pleasure and sporting dynamics. Package Design Pure Impulse, which will be available from September 2010, will emphasize the benefits of this sport coupe grace. Package Design Pure Impulse can be combined with a new exclusive version of the exterior, and combinations of colors and materials in the elements interior to help reflect the dynamic nature of the roadster. Salar Kamangar is often mentioned in discussions such as these. BMW X1 xDrive23d will get a 6-speed manual transmission.

Recently released and already well-proven BMW 5 sedan, from September 2010 will be equipped with intelligent BMW xDrive. Wheel-drive system with electronically controlled modification get BMW 550i xDrive with eight-cylinder engine. There will also be expanded engine lineup for the sedan BMW 535d: diesel version of the top BMW 5 Series Tools inline six-cylinder engine with BMW TwinPower Turbo technology with a capacity of 220 kW / 300 hp Beginning in September 2010 the market will be the fourth and most powerful diesel version of BMW 5 Series – BMW 535d sedan. The model will be equipped with in-line six-cylinder 3-liter, with the technology BMW TwinPower Turbo and direct fuel injection system Common Rail. Maximum torque is 600 N m and is reached at 1,750 rev / min at 4400 rev / min engine develops power KVt/300 220 liters. with. Turbocharger system, which is equipped with this world's most powerful six-cylinder diesel engine, operated in accordance with the principle of controlled turbocharger Variable Twin Turbo. And expands the list of additional equipment on all models of the BMW 7 Series. Now, cars can be equipped with a comfortable rear seats with electrically adjustable in versions for three passengers. Article taken from the Russian blog speed

Pump

To do this it must be connected to both terminals. If you take out the contact switch, should be reading the availability of current, and if the contact is inserted – there should be no evidence. To adjust the time of injection pump, as well as for removing and installing the pump requires special tools. In order to be to use these tools, you should use the following description. Removal and installation before removing the high pressure fuel pump motor set at top dead center.

To do this, remove the cover cylinder head and turn the engine until both valves will close the first cylinder, ie both valves should not have clearance. Further removal: Disconnect the throttle cable. All fuel unscrewed from the pump. To release the nut is best wrench of appropriate size, which was milled slot, so it can be to have a thick cloth to wrap the fuel lines connecting to collect fuel flowing. Plug removed from the fuel valve shut-off pump. Unplug from the wall of the pump. Pinion nut to release the fuel pump. To do this, insert a gear two screws 35-40 mm long and screwed into the threaded holes in the console gear pump must be located, respectively, to tighten the bolts.

Now gear pump can be shut down and release the nut. Remove the spring ring. Remove the gear pump with a stripper. It is screwed into the two threaded holes, average spindle pin down the shaft and remove the gear. Unscrew and remove the drive puller gear pump unscrew with the console attachment and remove it. If the pump is not unscrewed from the console, you do not need to set the time of injection fuel injection pump can be repaired or iterate through normal means, and in case of damage can be install new or replacement pump, or be old to repair a professional mechanic. When installing the pump, proceed as follows: Set the pump on the engine support brackets and are uniformly tighten the bolts to 19-26 Nm. Verify that the V-belt was on the pump shaft and the gear carefully fill in the shaft and tighten the screw nut with a torque of 60-70 Nm. Two screws to screw into the console again. that pump but could turn around. Tighten the compression nut on the fuel line 25 Nm for this use overlaid with a wrench with a slot. Once again, check that the engine all the time in a version of blind spot, Check phase distribution as described in the installation of the cylinder head. Conduct and all subsequent work described in this chapter, until the chickpeas to the V-belt. Set the time of injection can therefore to repair the power supply system

Evacuation Of Cars In Belarus

Evacuation of cars for long distance, that is, outside the city limits, of course, has its own specifics. In this case, come into force a number of factors not considered in the evacuation of automobiles in the city. For example, evacuation vehicles at close range may not fully use tow trucks ideal for transporting your car. In case of evacuation vehicles in Belarus, it is necessary to carefully select optimal type of tow truck, depending on the perspective of damage or the technical features of the car. We are talking about long distances and need to be sure that your car will deliver the reliability and safety, despite possible problems on the road. Tow in Belarus and the specifics of his work lies in the fact that driving should be an experienced driver, capable not only qualitatively implement loading the car, but it transportation over long distances. Indicator of quality of service is the timeliness of care.

Speaking of transportation vehicles at distances greater than the evacuation of cars Belarus, tow in this case will not be the best way to solve the problem. But within Belarus, the evacuation of existing services may well provide high quality and suitable price services provided for the evacuation of your car. Several important points during the evacuation of cars in Belarus: 1. Transporting your car should only be undertaken by a working technique, equipped with special fasteners to secure your machine on the platform of a tow truck. Non tow, as he is – must be clean. 2. Please make sure you have the necessary documents from the employee's service evacuation.

3. Not Take the time to monitor the process of loading your car onto the platform car service evacuation. 4. Do not allow a situation where your car is transported in an unknown direction you. 5. After loading the car for towing the platform no harm will put it on the handbrake, and verify whether the employee is securely fastened evacuation service your machine on the platform. 6. Please note that during the evacuation of cars in Belarus is not recommended to use tow truck, using the method of partial loading. These are the main points that are worth remembering if you "have" in the road and your car needs to evacuate the long haul. Evacuation of cars Belarus preferably should be a big firm, well-established at motorists for some time, or recommended to you by your friends or other motorists. So: Read reviews and comments motorists, pay attention to the quality of services rating agencies evacuated. All this is available on our website. Have a nice road.

Power Plus

Found: reduce consumption of gasoline was exactly one liter. And it's good. What to do next? According to the recommendations of application of the biocatalyst, replaced the fuel filter. It was really packed. Physically, this is easily explained. The catalyst was cleaned the fuel system, the flow of gasoline tubules moved all the dirt in the filter. Everything is logical. He looked into the carburetor.

It occurred to me that there is full of dirt. Nothing like that. Everything is clean. Smoked, screwed the bolts back – that's all prevention. Incidentally, the second filter replacement, I made a week later.

It is unusual to quickly clogged. But in later no problems. Frankly, I am now about the planned replacement of filter does not paryus. In fact, why change the filter if it is clean? I have kept the biocatalyst in the "glove". Nothing special with it did not happen. But the familiar Tanker said that the bottle can not be left in a car in summer or winter in the sun at night. Keep better at temperatures between +5 and +30. And only a microclimate in an apartment or garage. It is necessary to fill the tank – took a bottle with him. And if you forgot – no particular trouble. Zalesh with biocatalysts in next time. In spring and autumn you can bottle all the time, carry with them. One bottle biocatalyst Power Plus MPG I have enough for twelve full tanks is approximately 480 liters of gasoline. Maybe I'm particularly settlement instructions and has not adhered to.

Road Safety Ministry

Novelties SDA, which will come into force from 20.11.2010 raised a number of vital points about how drivers and pedestrians alike. So, check your windows tinted foreign cars on the road can now be any traffic police inspector. Previously done it could only state inspector of technical supervision. Department of Road Safety Ministry of the Interior is directed to place an explanation on the practical application of Section 3.1 of Article 12.5 of the Administrative Code, which provides administrative responsibility for the excess of the norms of toning. In the case of visual signs of an administrative offense, that is, if excessively tinted inspector stops vehicle and provides measurement of light transmission. In the case of non-conformity with the established requirements of the inspector in respect of the offending driver and administrative material such vehicles will pay a fine of 500 rubles. At the same time to determine the degree of toning, which is called 'the eye' nobody has the right. Must use special certified devices.

Pedestrians can now feel on the road to greater security. Now removed all the double interpretation of how the driver must give way to pedestrians. Now the SDA says that drivers must give way to pedestrians who has authority, but it is not clear exactly how. After all, you see, in this case, the wording could be interpreted as a brake or drive fast – and so, and so it means to yield. The amendments to the PDD clearly states that driver of a vehicle approaching an unregulated pedestrian crossing must slow down or stop for pedestrians crossing the carriageway or stepped on it to go. Russian drivers have to learn to pass sections with a circular motion for a new way. Over the last few years in the traffic police authorities have repeatedly received complaints from drivers of the difficulties and bottlenecks in a circular motion. Now everything is different.

If the priority is now entering the circle, and from November 20, when the amendments come into force in the SDA, the principal will have drivers who are on the range – go for it, or leave. In fact, the rules change the other way around, and they need to get used to. Primarily, these changes have been made in order to avoid potential congestion in a circular motion. And it turns out that to enter the circle can do everything, but leave an already problematic, especially in heavy traffic. Now, when entering the circle will be installed road signs' circular motion 'in combination with a' Yield ', or' movement is prohibited without stopping. " That is, in a circle and when leaving it with the drivers will be a priority in the movement.

Lamborghini Ferruccio

Almost all of automotive history is built on individualism. Exalted Henry Ford, Enzo Ferrari, Ferdinand Porsche, Ettore Bugatti, Lamborghini Ferruccio not only founded the company's own name, but also embodied the enforce their personal views about the ideal vehicle. However, individualism departs when it comes to the legendary brand Maserati, created by six brothers, who for many years a model of technical excellence and unbridled power, the embodiment of collective engineering genius. Auto racing – the engine of progress in the children of Catholic parents, Rodolfo and Caroline had seven Maserati, but one of them died in infancy, and six of fate was destined to become the founders of the company, famous for his fast cars. Each of the brothers – Carlo (1881 born), Bindo (1883), Alfieri (1887), Mario (1890), Ettore (1894) and Ernesto (1898) – contributed to the fact that during many years is called 'style Maserati'. Passion for cars older brothers instilled Maserati Carlo.

He worked as a manager at the firm Junior, as well as engaged in the development of aircraft engines. His other passion was racing. Carlo attracted by the opportunity not only to taste of speed, but also to understand the limits of technical possibilities of cars in extreme conditions. For an engineer to the bone it was very important because the technology of that time did not are reliable. In 1907 Carlo Bianchi under the flags of the team takes part in competitions. Low-voltage circuit breaker cranky ignition system a few times out of order, and the young have to change his Maserati on the go.

© 2012-2017 The National Science Fair All Rights Reserved -- Copyright notice by Blog Copyright